#1 Global Leader in Data Protection & Ransomware Recovery

How to troubleshoot CIM hardware monitoring

KB ID: 1568
Product: Veeam ONE
Veeam Management Pack for Microsoft System Center
Version: 5.7, 6.x, 7.x, 8.x
Published: 2012-07-11
Last Modified: 2020-11-17
mailbox
Get weekly article updates
By subscribing, you are agreeing to have your personal information managed in accordance with the terms of Veeam's Privacy Notice.

Cheers for trusting us with the spot in your mailbox!

Now you’re less likely to miss what’s been brewing in our knowledge base with this weekly digest

error icon

Oops! Something went wrong.

Please try again later.

Challenge

The CIM API allows Veeam products to receive up-to-date information without requesting hardware refreshes, but this requires a separate connection, and if that connection cannot be made, the hardware data will be collected as it was in earlier versions, and request periodic hardware refreshes on the hosts.

Cause

There are the following ways in which the connection to the CIM API may fail:
  1. CIM Interaction is not enabled on the account used to connect to vCenter and ESX(i) hosts, or the account does not have direct access to the ESX(i) hosts. 
  2. The host name cannot be resolved from the collector or collectors.
  3. The CIM port is closed on the ESX/ESXi host or blocked by a firewall.
  4. The CIM server process may not be running.
  5. Updated hardware data are unavailable on the host for some reason.
  6. The time on the ESX host is different from the time in the domain.

Solution

The solutions below will allow you to troubleshoot and resolve the causes of CIM connection failures listed above:
  1. "CIM Interaction" should be enabled on the account used to monitor vCenter and the ESX/ESXi hosts. This is included in the Install Guide, but may have been overlooked, such as on an upgrade where the account had already been created.
  2. The host name must resolve from the collector system. The collector uses its existing connection to the vCenter server to obtain a name for the host, which is visible in the vSphere client when you select the host, go to the Configuration tab and select "DNS and Routing" on the left. If this name is unable to resolve from each collector that will monitor the host, or it contains a value such as "localhost" instead of the actual name and domain, the collector won't be able to connect to the host directly. If the name appears correct, but is unable to resolve anyway, you may need to update the DNS server or check for NAT firewalls on the network between the collector and host.
  3. The host must be accessible from the collector over port TCP/5989. The collector will communicate with the host using HTTPS over this port, so it must be accessible over the network through any firewalls and on the host itself, as described in VMware KB1013080. Note: if the port is closed, the failure to communicate with the host may interfere with the collector's attempts to retrieve data from other hosts.
  4. The CIM server must be running on the host to respond to the collector's requests for data. VMware has addressed problems in ESX 3.5 (VMware KB1009607) and ESX 4.0 prior to version 4.1 (VMware KB2011592).
  5. Check hardware data availability on VMware side. Open VIClient, select the affected host, go to "Hardware" tab, click "Reset sensors" and verify you do not have a warning saying "No new host data available. If from time to time you can see warnings like this, the subsequent troubleshooting lies on VMware side.User-added image
  6. The time on the ESX(i) hosts has to be synchronized with the domain, where Veeam is installed.

More Information

If you have any questions or problems, please contact Veeam Support at http://www.veeam.com/support
To submit feedback regarding this article, please click this link: Send Article Feedback
To report a typo on this page, highlight the typo with your mouse and press CTRL + Enter.

Spelling error in text

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Thank you!

Thank you!

Your feedback has been received and will be reviewed.

Oops! Something went wrong.

Please try again later.

You have selected too large block!

Please try select less.

KB Feedback/Suggestion

This form is only for KB Feedback/Suggestions, if you need help with the software open a support case

By submitting, you are agreeing to have your personal information managed in accordance with the terms of Veeam's Privacy Notice.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Verify your email to continue your product download
We've sent a verification code to:
  • Incorrect verification code. Please try again.
An email with a verification code was just sent to
Didn't receive the code? Click to resend in sec
Didn't receive the code? Click to resend
Thank you!

Thank you!

Your feedback has been received and will be reviewed.

error icon

Oops! Something went wrong.

Please try again later.